Lumber Totally Explained

Everything about Lumber totally explained

Lumber or timber is wood in any of its stages from felling through readiness for use as structural material for construction, or wood pulp for paper production. often refers to the wood contents of standing, live trees that can be used for lumber or fiber production, although it can also be used to describe sawn lumber whose smallest dimension isn't less than 5 inches (127 mm).
Lumber is supplied either rough or finished. Besides pulpwood, rough lumber is the raw material for furniture-making and other items requiring additional cutting and shaping. It is available in many species, usually hardwoods. Finished lumber is supplied in standard sizes, mostly for the construction industry, primarily softwood from coniferous species including pine, cedar, hemlock, fir and spruce, but also some hardwood for high-grade flooring.

Dimensional lumber

Dimensional lumber is a term used for lumber that's finished/planed and cut to standardized width and depth specified in inches. Examples of common sizes are 2×4 (also two-by-four and other variants such as four-b'-two in Australia), 2×6, and 4×4. The length of a board is usually specified separately from the width and depth. It is thus possible to find 2×4s that are four, eight, or twelve feet in length. In the United States the standard lengths of lumber are 6, 8, 10, 12, 14, 16, 18, 20, 22, and 24 feet.

Softwood dimensional lumber sizes
Nominal	Actual	Nominal	Actual
1 × 2	¾ × 1½ in (19×38 mm)	2 × 2	1½ × 1½ in (38×38 mm)
1 × 3	¾ × 2½ in (19×64 mm)	2 × 3	1½ × 2½ in (38×64 mm)
1 × 4	¾ × 3½ in (19×89 mm)	2 × 4	1½ × 3½ in (38×89 mm)
1 × 6	¾ × 5½ in (19×140 mm)	2 × 6	1½ × 5½ in (38×140 mm)
1 × 8	¾ × 7¼ in (19×184 mm)	2 × 8	1½ × 7¼ in (38×184 mm)
1 × 10	¾ × 9¼ in (19×235 mm)	2 × 10	1½ × 9¼ in (38×235 mm)
1 × 12	¾ × 11¼ in (19×286 mm)	2 × 12	1½ × 11¼ in (38×286 mm)
3 × 4	2½ × 3½ in (64×89 mm)	2 × 14	1½ × 13¼ in (38×337 mm)
4 × 4	3½ × 3½ in (89×89 mm)	6 × 6	5½ × 5½ in (140×140 mm)
4 × 6	3½ × 5½ in (89×140 mm)	8 × 8	7¼ × 7¼ in (184×184 mm)

Solid dimensional lumber typically is only available up to lengths of 24 ft, yet since builders have a need for lengths beyond that for roof construction (rafters), builders use "finger-jointed" lumber that can be up to 36 ft long in 2×6 size (see Engineered Lumber below). Finger-jointed lumber is also widely used for smaller lengths like studs, the vertical members of a framed wall. Pre-cut studs save a framer a lot of time as they're pre-cut by the manufacturer to be used in 8 ft, 9 ft & 10 ft ceiling applications, which means they've removed a few inches of the piece to allow for the sill plate and the double top plate with no additional sizing necessary by the framer.
In the Americas, two-bys (2×4s, 2×6s, 2×8s, 2×10s, and 2×12s), along with the 4×4, are common lumber sizes used in modern construction. They are the basic building block for such common structures as balloon-frame or platform-frame housing. Dimensional lumber made from softwood is typically used for construction, while hardwood boards are more commonly used for making cabinets or furniture.
The nominal size of a board varies from the actual size of the board. This is due to planing and shrinkage as the board is dried. This results in the final lumber being slightly smaller than the nominal size. Also, if the wood is surfaced when it's green, the initial dimensions are slightly larger (for example 1/16 in bigger for up to 4 in nominal lumber, ⅛ in for 5 in and 6 in nominal lumber, ¼ in bigger for larger sizes). As the wood dries, it shrinks and reaches the specified actual dimensions.

Non-North American sizes

Examples of dimensional lumber sizes (softwood and hardwood)
Inch name	Sawed	Swedish	Australian
2 × 4	50 × 100 mm	45 × 95 mm	45 × 90 mm
1 × 3	25 × 75 mm	22 × 70 mm	19 × 70 mm
3 × 3	75 × 75 mm	70 × 70 mm
2 × 7	50 × 175 mm	45 × 170 mm	Not used
2 × 3	50 × 75 mm	45 × 70 mm	45 × 70 mm
1 × 4	25 × 100 mm	22 × 95 mm	19 × 90 mm
1 × 5	25 × 125 mm	22 × 120 mm	19 × 120 mm
2 × 5	50 × 125 mm	45 × 120 mm	45 × 120 mm

Outside North America sizes of timber can vary slightly. Sizes are, in some cases, based on the imperial measurement and referred to as such; in other cases the sizes are too far removed from the imperial size to be referred to by imperial measurement. Lengths are sold every 300 mm (a metric approximation of 1 ft). Common sizes are similar to the North American equivalent; 2.4, 2.7, 3.0, 3.6, 4.2, 4.8, 5.4, 6.0.

Hardwoods

Hardwood dimensional lumber sizes
Nominal	Surfaced 1 Side (S1S)	Surfaced 2 sides (S2S)
½ in	⅜ in	5/16 in
⅝ in	½ in	7/16 in
¾ in	⅝ in	9/16 in
1 in or 4/4 in	⅞ in	13/16 in
1¼ in or 5/4 in	1⅛ in	1-1/16 in
1½ in or 6/4 in	1⅜ in	1-5/16 in
2 in or 8/4 in	1-13/16 in	1¾ in
3 in or 12/4 in	2-13/16 in	2¾ in
4 in or 16/4 in	3-13/16 in	3¾ in

In North America sizes for dimensional lumber made from hardwoods varies from the sizes for softwoods. Boards are usually supplied in random widths and lengths of a specified thickness, and sold by the board-foot (144 cubic inches, 1/12th of a cubic foot). This doesn't apply in all countries, for example in Australia many boards are sold to timber yards in packs with a common profile (dimensions) but not necessarily of consisting of the same length boards. Hardwoods cut for furniture are cut in the fall and winter, after the sap has stopped running in the trees. If hardwoods are cut in the spring or summer the sap ruins the natural color of the timber and deteriorates the value of the timber for furniture.
Also in North America hardwood lumber is commonly sold in a “quarter” system when referring to thickness. 4/4 (four quarters) refers to a one-inch thick board, 8/4 (eight quarters) is a two-inch thick board, etc. This system isn't usually used for softwood lumber, although softwood decking is sometimes sold as 5/4 (actually one inch thick).

Engineered lumber

Engineered lumber is lumber created by a manufacturer and designed for a certain structural purpose. The main categories of engineered lumber are:

Laminated Veneer Lumber (LVL) – LVL comes in 1-3/4 inch thicknesses with depths such as 9-1/2, 11-7/8, 13, 16, 18, or 24 inches, and are typically doubled or tripled up. They function as beams to provide support over large spans, such as removed support walls and garage door openings, places where dimensional lumber isn't structurally sound to use, and also in areas where a heavy load is bearing from a floor, wall or roof above on a somewhat short span where dimensional lumber isn't practical. This type of lumber can't be altered by holes or notches anywhere within the span or at the ends, as it compromises the integrity of the beam, but nails can be driven into it wherever necessary to anchor the beam or to add hangers for I-joists or dimensional lumber joists that terminate at an LVL beam.
Wood I-joists – Sometimes called "TJI®" or "Trus Joists®", both of which are brands of wood I-joists, they're used for floor joists on upper floors and also in first floor conventional foundation construction on piers as opposed to slab floor construction. They are engineered for long spans and are doubled up in places where a wall will be placed over them, and sometimes tripled where heavy roof-loaded support walls are placed above them. They consist of a top and bottom chord/flange made from LVL with a webbing in-between made from oriented strand board (OSB). The webbing can be removed up to certain sizes/shapes according to the manufacturer's or engineer's specifications, but for small holes, wood I-joists come with "knockouts", which are perforated, precut areas where holes can be made easily, typically without engineering approval. When large holes are needed, they can typically be made in the webbing only and only in the center third of the span; the top and bottom chords can't be cut. Sizes and shapes of the hole, and typically the placing of a hole itself, must be approved by an engineer prior to the cutting of the hole and in many areas, a sheet showing the calculations made by the engineer must be provided to the building inspection authorities before the hole will be approved. Some I-joists are made with W-style webbing like a truss to eliminate cutting and allow ductwork to pass through.
Finger-Jointed Lumber – Solid dimensional lumber lengths typically are limited to lengths of 22 to 24 feet, but can be made longer by the technique of "finger-jointing" lumber by using small solid pieces, usually 18 to 24 inches long, and joining them together using finger joints and glue to produce lengths that can be up to 36 feet long in 2×6 size. Finger-jointing also is predominant in precut wall studs.
Glu-lam Beams – Created from 2×4 or 2×6 stock by gluing the faces together to create beams such as 4×12 or 6×16. LVL beams have taken their place in most home construction.
Manufactured Trusses – Trusses are used in home construction as bracing to support the roof rafters in the attic space. It is seen as an easier installation and a better solution for supporting roofs as opposed to the use of dimensional lumber's struts and purlins as bracing. In the southern USA and other parts, stick-framing with dimensional lumber roof support is still predominant. The main drawback of trusses is that less attic space is usable.
Oriented Strand Board (OSB) – OSB is made by laminating large, thin wood chips with glue, such that the grain orientation of the chips is random, making the OSB panels equally stiff in all directions. OSB has replaced plywood for use as exterior wall sheathing and roof decking (7/16 inch minimum thickness) and in second-story flooring (3/4 inch thickness in a tongue-and-groove interlocking pattern), which is nailed and glued to the I-joists. OSB used in wall sheathing and roof decking will swell if exposed to the elements for even a brief time and must be replaced; therefore, it's covered by a weatherproof membrane such as felt or spun-bonded olefin (Tyvek®) to protect it, secured with plastic cap nails. House wrapping is used on areas which will be sheathed with vinyl siding. 3/4 inch tongue-and-groove OSB flooring is coated to protect it from the elements for a short time until the structure is roofed over. Moisture resistant OSB is often specified for use as a roof underlayment.

Defects in lumber

Defects occurring in Timber are grouped into the following five divisions:

Defects due to conversion

During the process of converting timber to commercial form, the following defects may occur:

Chip mark

Diagonal grain

Torn grain

Wane

Defects due to fungi

Fungi attack timber only when the following two conditions are satisfied simultaneously:

The moisture content of the timber is above 20%

There is presence of air and warmth for the growth of fungi. If any of the above condition is absent, decay of wood due to fungi wouldn't occur. Hence, dry wood due having moisture content less than 20 per cent will remain sound for centuries. Similarly, wood submerged in water won't be attacked by fungi because of absence of air. Following defects are caused in timber by fungi:

Blue stain

Brown rot

Dry rot

Heart rot

Sap stain

Wet rot

White rot

Defects due to insects

Following are the insects which are usually responsible for the decay of timber:

Beetles

Marine Borers

Termites

Defects due to natural forces

The main natural forces responsible for causing defects in timber are two, namely, abnormal growth and rupture of tissues.

Defects due to seasoning

Defects due to seasoning are the number one cause for splinters and slivers.

Preservatives

Timber or lumber may be treated with a preservative that protects it from being destroyed by insects, fungus or exposure to moisture. Generally this is applied through combined vacuum and pressure treatment. The preservatives used to pressure-treat lumber are classified as pesticides; due to potential hazards to humans and the environment, some are being phased out. Treating lumber provides long-term resistance to organisms that cause deterioration. If it's applied correctly, it extends the productive life of lumber by five to ten times. If left untreated, wood that's exposed to moisture or soil for sustained periods of time will become weakened by various types of fungi, bacteria or insects.

Timber framing

Timber framing is a style of construction which uses heavier framing elements than modern stick framing, which uses dimensional lumber. The timbers originally were tree boles squared with a broadaxe or adze and joined together with joinery without nails. A modern imitation with sawn timbers is growing in popularity in the United States.
One of the most conventional framing methods is the Neumann Notch, which involves a thirty-two degree angling of adjoining lumber and then a right-angled wedge with an eighteen degree cusp fitted between the lumber before being bolted. This convention was pioneered by Daniel R. Neumann, a carpenter from Germany, that was responsible for the structural development of the Massachusetts Bay Colony in 1630. This framing convention spread to construction sites in other colonies, most famously Plymouth and Concord. Neumann's notched framing then was adopted by carpenters and construction companies and this framing convention is still used today in traditional frame sets.
Another somewhat less conventional method for framing is known as the "New-style" binding. The basic setup of the New-style binding was developed by Austin D. New, a Mormon settler in Salt Lake City, Utah during the 1800s. The basic structure of the New-style binding involves a set-up of two similar sized logs set against each other perpendicularly and lashed together with hemp rope. This technique was used to construct many of the early houses of the Mormon settlers due to its ease of use and durability. Eventually the New-style binding became obsolete as the settlers began constructing homes out of the more traditional brick and mortar.

Terminology

In the United Kingdom and Australia, "timber" is a term also used for sawn wood products (that is, boards), whereas generally in the United States and Canada, the product of timber cut into boards is referred to as lumber. In the United States and Canada sawn wood products of five inches (127 mm) (nominal size) diameter or greater are sometimes called "timbers".

Further Information

Get more info on 'Lumber'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://lumber.totallyexplained.com">Lumber Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.